Product Description: ECONOMIC FUMED SILICONE RUBBER FOR MOLDING
● Compliance with FDA
● Good transparency and mechanical properties
● Good yellowing resistance and stable processability
Main Applications:
● Molded products with high requirement for transparency
Typical Data:
|
Properties |
Product Data |
Test Method |
|||||||
|
NE-9530 |
NE-9540 |
NE-9550 |
NE-9560 |
NE-9570 |
NE-9580 |
NE-9590 |
|||
|
Appearance |
Transparent, no extraneous matter. |
Visual Inspection |
|||||||
|
Density, g/cm3 |
1.06～1.10 |
1.09～1.15 |
1.12～1.18 |
1.14～1.20 |
1.17～1.23 |
1.18～1.25 |
1.19～1.26 |
ASTM D792 |
|
|
Curing
|
Hardness, Shore A |
30±2 |
40±2 |
50±2 |
60±2 |
70±2 |
80±2 |
86±2 |
ASTM D2240 |
|
Tensile Strength, MPa, ≥ |
8.0 |
8.5 |
8.0 |
6.0 |
|||||
|
Elongation at Break, %, ≥ |
600 |
500 |
400 |
300 |
200 |
120 |
|||
|
Tension Set, %, ≤ |
8 |
6 |
|||||||
|
Tear Strength, Die C kN/m ≥ |
15 |
20 |
25 |
20 |
10 |
ASTM D624 |
|||
|
Post- curing
|
Hardness, Shore A |
32±2 |
44±2 |
55±2 |
66±2 |
74±2 |
84±2 |
/ |
ASTM D2240 |
|
Tensile Strength, MPa, ≥ |
6.5 |
7.0 |
8.0 |
7.0 |
/ |
ASTM D412 |
|||
|
Elongation at Break, %, ≥ |
500 |
400 |
300 |
200 |
150 |
/ |
|||
|
Tear Strength, Die C kN/m ≥ |
10 |
16 |
18 |
16 |
/ |
ASTM D624 |
|||
|
Compression Set, 180℃*22h ≤ |
58 |
50 |
48 |
45 |
35 |
ASTM D395 |
|||
|
Rebound Resilience, %, ≥ |
50 |
45 |
40 |
35 |
/ |
||||
|
Volume Resistivity, Ω ▪cm, ≥ |
1×1015 |
IEC 60093 |
|||||||
|
Dielectric Strength, kV/mm, ≥ |
20 |
IEC 60243 |
|||||||
● Physical data in the above table is for reference only.
● Vulcanization condition: 175℃*5Min. ●Post-curing condition:200℃* 4h
● Ratio of curing agent liquid 2,5-Dimethyl-2,5-di(tert-butylperoxy) hexane: 0.65%.
●The supplied test report is obtained by the Quality Inspection Department with the curing conditions and testing method of the company; due to the difference of curing conditions and testing method, we can’t guarantee that both parties obtain the same testing result, and we suggest that users should use the test data obtained under their own testing conditions as the reference for service performance. All the above performance data and application recommendations are only a reference for use on the service performance of product, instead of a guarantee on the effectiveness or general applicability of our products under a certain application.
Related material download:
ROHS and Other Restricted Substances Test for Silicone Rubber
Substances of Very High Concern Test(SVHC) for Silicone Rubber
MSDS-Economic Fumed Silicone Rubber for Molding
LFGB Test for Fumed Silicone RubberFDA Test for Fumed Silicone Rubber
Economic Fumed Silicone Rubber for Molding NE-95 Series TDS
